Welcome to My Website The world is leading online retail marketplace based in China
Safe and Convenient Shopping on My Website
PayPal, the world is most loved way to pay
Diverse payment options
Customer Support We provides attentive customer services on every aspect
Top Selling
-
$429.99
-
$419.99 $379.99
Save: 10% off -
$194.99 $185.00
Save: 5% off -
$489.99 $469.99
Save: 4% off -
$149.99
-
$419.99 $259.99
Save: 38% off -
$59.99 $34.99
Save: 42% off
Home :: Store News :: Super KTMFLASH Car ECU Programmer KTMFLASH User Manual |
Store News
Super KTMFLASH Car ECU Programmer KTMFLASH User Manual
|Super KTMFLASH Car ECU Programmer KTMFLASH User Manual
KTMFLASH Car ECU Programmer is a new ecu flash programming tool. KTM FLASH ECU Programmer & transmission power upgrade tool can read the chip data, change the engine computer, read transmission data etc at a high speed. Gsunlight.com How To Use KTMFLASH Car ECU Programmer KTM FLASH ECU Programmer & transmission power upgrade tool Switch board.
How to use KTM Flash Switch board?
1. The switch board is designed to work with J2534, this device uses the Ktag cables so the user can refer to the Ktag wiring diagram.
2. Recommend you use OpenPort 2.0 ecu flash cable as the protocol conversion equipment and work with PC.
3. There are 3 types of Bosch Infineon ECU :
1) The Infineon ECU before TPROT8.
2) TPROT8–10
3) The Infineon ECU after TPROT10 which is what we call GPT encrypted.
4. The Infineon ECU before TPROT8 is not encrypted, you directly uses the BOOT point
grounding, then follow the Ktag user manual to wire the cable and read the data.
5.For TPROT8–10,the Bosch Company set the anti-debugging mode, reading EEPROM needs no password and reading Flash needs password.
Therefore, during the reading process, there is an extra CNF1, Boot outputs low level and CNF1 outputs high level. When reading, Boot needs to add one small resistor and ground it. CNF1 to
connect one 470ohm-2K resistance, then connect 3.3V, it’s very important, otherwise the ECU will be burnout.
2 tips on reading the data:
1) BOOT and CNF1 must be connected when reading data.
2) Only connect BOOT not CNF1 When reading the password, otherwise the password can’t be read out. Also you can follow the Ktag wiring diagram because Ktag controls the CNF1 turn on
and off, so it can’t be disconnected. When reading the password, you turn the two switches to the automatic mode, and to the On mode when reading the data, when the software prompts, you
choose ” Manually” then follow the message to turn on or off.
6. For GPT encrypted ECU, the S1, S2 and Boot cable are needed to connected when reading password, and the S1, S2 don’t need to be connected when reading data.
Gsunlight.com-- China OBD2 Tool, Automotive Diagnostic Tools, Car Key Programmer, OBD2 ECU chip tuning tool Center.
Contact information:
Website: www.Gsunlight.com
Email: gsunlight@outlook.com
Skype: gsunlight@outlook.com
Whatapp: +86-13691674080
Other news for Tuesday 19 June, 2018
View all news for Tuesday 19 June, 2018 on one page
News for Sunday 17 June, 2018
View all news for Sunday 17 June, 2018 on one page
Recent News
- Friday 15 June, 2018
- Monday 11 June, 2018
- Sunday 10 June, 2018
- Friday 08 June, 2018
- Thursday 07 June, 2018