Tuesday 19 June, 2018 |

Super KTMFLASH Car ECU Programmer KTMFLASH User Manual

by Administrator | post a comment

Super KTMFLASH Car ECU Programmer KTMFLASH User Manual

KTMFLASH Car ECU Programmer is a new ecu flash programming tool. KTM FLASH ECU Programmer & transmission power upgrade tool can read the chip data, change the engine computer, read transmission data etc at a high speed. Gsunlight.com How To Use KTMFLASH Car ECU Programmer KTM FLASH ECU Programmer & transmission power upgrade tool Switch board.

How to use KTM Flash Switch board?

1. The switch board is designed to work with J2534, this device uses the Ktag cables so the user can refer to the Ktag wiring diagram.

2. Recommend you use OpenPort 2.0 ecu flash cable as the protocol conversion equipment and work with PC.

3. There are 3 types of Bosch Infineon ECU :

1) The Infineon ECU before TPROT8.

2) TPROT8–10

3) The Infineon ECU after TPROT10 which is what we call GPT encrypted.

4. The Infineon ECU before TPROT8 is not encrypted, you directly uses the BOOT point

grounding, then follow the Ktag user manual to wire the cable and read the data.

5.For TPROT8–10,the Bosch Company set the anti-debugging mode, reading EEPROM needs no password and reading Flash needs password.

Therefore, during the reading process, there is an extra CNF1, Boot outputs low level and CNF1 outputs high level. When reading, Boot needs to add one small resistor and ground it. CNF1 to

connect one 470ohm-2K resistance, then connect 3.3V, it’s very important, otherwise the ECU will be burnout.

2 tips on reading the data:
 
1) BOOT and CNF1 must be connected when reading data.
 
2) Only connect BOOT not CNF1 When reading the password, otherwise the password can’t be read out. Also you can follow the Ktag wiring diagram because Ktag controls the CNF1 turn on

and off, so it can’t be disconnected. When reading the password, you turn the two switches to the automatic mode, and to the On mode when reading the data, when the software prompts, you

choose ” Manually” then follow the message to turn on or off.

6. For GPT encrypted ECU, the S1, S2 and Boot cable are needed to connected when reading password, and the S1, S2 don’t need to be connected when reading data.

Gsunlight.com-- China OBD2 Tool, Automotive Diagnostic Tools, Car Key Programmer, OBD2 ECU chip tuning tool Center.

Contact information:

Website: www.Gsunlight.com
Email: gsunlight@outlook.com
Skype: gsunlight@outlook.com
Whatapp: +86-13691674080

ODIS VW AUDI 5 in 1 ODIS 4.3.3 Software Download With ODIS Engineering 8.1.3 Download ODIS 4.3.3 Install user manul

by Administrator | post a comment

ODIS 4.3.3 Download Software can work for VW AUDI Audi, Seat, Skoda, Volkswagen, VW Commercial, Lamborghini, Bentley, Bugatti. ODIS 4.3.3 Download Software With ODIS Engineering 8.1.3 Download, Elsawin 5.3, Etka 8.0 Software well installed on hard disk can ready To use. Gsunlight.com ODIS 4.3.3 Download Software With ODIS Engineering 8.1.3 Download ODIS 4.3.3 Install Guide.

ODIS 4.3.3 Download 5 in 1 VAG ODIS 4.3.3 Software With ODIS Engineering 8.1.3 Download, Elsawin 5.3, Etka 8.0 Software


Note: Gsunlight.com This 5 in 1 odis 4.3.3 download software HDD including: V4.3.3 ODIS download software for audi and vw, Elsawin 5.3, VW Audi etka parts catalogue V8.0, vag odis engineering 8.1.3 5 in 1 software in one hard disk that can ready to use.

Gsunlight.com ODIS 4.3.3 Install Guide:

Softing_OK_UPD_link:

https://mega.nz/#!FcVgxSYT!6mEcIN2nQqMcwF4TZA31JVJx3WEGI4pjuAb1TyPmO7Q

Follow this steps :

1.- Install ODIS-S as usual but NO restart !
2.- Rename the folder Softing from Program Files (x86) (or Program Files) to Softing.ori
3.- Copy the downloaded Softing folder to Program Files (x86) (or Program Files).
4.- Restart
5.- Install Postsetup
6.- Install ODIS-E 8.1.3 as usual
7.- Thats All !

UPDATE :
– Replace Softing directory with the updated directory and you get this…

Notice of gsunlight.com ODIS 4.3.3 Download Software

Before running the odis engineer , need to change the computer time to 20170201
Before running the ETKA , need to change the computer time to 2012.01.01
Before running other softwares, the current time is OK
Elsawin software ID and password all are "admin "

Gsunlight.com-- China OBD2 Tool, Automotive Diagnostic Tools, Car Key Programmer, OBD2 ECU chip tuning tool Center.

Contact information:

Website: www.gsunlight.com
Email: gsunlight@outlook.com
Skype: gsunlight@outlook.com
Whatsapp: +86-13691674080

News for Sunday 17 June, 2018

• Super DSP 3 Password For Super DSP III OBD Tool Super DSP III Plus Mileage Correction

View all news for Sunday 17 June, 2018 on one page

Recent News

• Friday 15 June, 2018
• Monday 11 June, 2018
• Sunday 10 June, 2018
• Friday 08 June, 2018
• Thursday 07 June, 2018

News archive