Friday 15 June, 2018 |

How To Use KTMFLASH Car ECU Programmer & transmission power upgrade tool Switch board

by Administrator | post a comment

How To Use  KTM FLASH ECU Programmer & transmission power upgrade tool Switch board

KTMFLASH Car ECU Programmer is a new ecu flash programming tool. KTM FLASH ECU Programmer & transmission power upgrade tool can read the chip data, change the engine computer, read transmission data etc at a high speed. Gsunlight.com How To Use KTMFLASH Car ECU Programmer KTM FLASH ECU Programmer & transmission power upgrade tool Switch board.

KTM FLASH KTMFLASH Car ECU Programmer KTM ECU Flash Supports VAG DQ200 DQ250 Infineon Bosch


What’s gsunlight.com KTM FLASH KTMFLASH Car ECU Programmer:

The KTMFlash is a ECU Programmer & transmission power upgrade tool which can read the chip data, change the engine computer, read transmission data etc at a high speed.

Gsunlight.com KTM FLASH ECU Programmer & transmission power upgrade tool Functions:

1.Read the car ecu via OBD.
3.Read the BOOT mode according to the chip model
4.Read the encrypted ECU password (Read the password of encrypted ECU first, then read data)
5. Support cars made in China with ME17 TC1728/1767 for data reading & writing and password reading.

Gsunlight.com How To Use KTMFLASH Car ECU Programmer KTM FLASH ECU Programmer & transmission power upgrade tool Switch board:

1. The switch board is designed to work with J2534, this device uses the Ktag cables so the user can refer to the Ktag wiring diagram.
2. Recommend you use OpenPort 2.0 ecu flash cable as the protocol conversion equipment and work with PC.
3. There are 3 types of Bosch Infineon ECU :
 1) The Infineon ECU before TPROT8.
 2) TPROT8-10
 3) The Infineon ECU after TPROT10 which is what we call GPT encrypted.
4. The Infineon ECU before TPROT8 is not encrypted, you directly uses the BOOT point
grounding, then follow the Ktag user manual to wire the cable and read the data.
5.For TPROT8-10,the Bosch Company set the anti-debugging mode, reading EEPROM needs no password and reading Flash needs password.
 Therefore, during the reading process, there is an extra CNF1, Boot outputs low level and CNF1 outputs high level. When reading, Boot needs to add one small resistor and ground it. CNF1 to connect one 470ohm-2K resistance, then connect 3.3V, it’s very important, otherwise the ECU will be burnout.
2 tips on reading the data:
 1) BOOT and CNF1 must be connected when reading data.
 2) Only connect BOOT not CNF1 When reading the password, otherwise the password can’t be read out. Also you can follow the Ktag wiring diagram because Ktag controls the CNF1 turn on and off, so it can’t be disconnected. When reading the password, you turn the two switches to the automatic mode, and to the On mode when reading the data, when the software prompts, you choose ” Manually” then follow the message to turn on or off.
6. For GPT encrypted ECU, the S1, S2 and Boot cable are needed to connected when reading password, and the S1, S2 don’t need to be connected when reading data.

Gsunlight.com-- China OBD2 Tool, Automotive Diagnostic Tools, Car Key Programmer, OBD2 ECU chip tuning tool Center.

Contact information:


Website: www.gsunlight.com
Skype: gsunlight@outlook.com
Email: gsunlight@outlook.com
What;s app: +86 13691674080

Other news for Friday 15 June, 2018

• Ross Tech VCDS 18.2.1 Crack line Genuine 18.2.1 vag com diagnostic Interface Not Found problem Solution

View all news for Friday 15 June, 2018 on one page

News for Monday 11 June, 2018

• GM Tech 2 Scanner Full Package Vetronix Tech 2 Clone With GM Tech 2 32MB PCMCIA Memory CARD For GM,OPEL,SAAB,ISUZU,SUZUKI and Holden

View all news for Monday 11 June, 2018 on one page

Recent News

• Sunday 10 June, 2018
• Friday 08 June, 2018
• Thursday 07 June, 2018
• Wednesday 06 June, 2018
• Tuesday 05 June, 2018

News archive